Cambridge SoundWorks Home Theater System MC630HD User Manual

 
Contents  
Newton Series HD  
High Performance  
Loudspeaker  
Introduction ................................................................... 4  
Product Contents .......................................................... 4  
Inspecting for Damage .................................................. 4  
System Configuration .................................................... 5  
Speaker Placement ....................................................... 5  
Wiring ............................................................................ 6  
Speaker Mounting ......................................................... 7  
Horizontal Use ............................................................... 8  
Bass Contour Switch .................................................... 9  
Enclosure Cleaning ...................................................... 9  
In Case of Difficulty .................................................... 9  
Specifications ............................................................ 10  
Dimensions  
................................................................. 10  
- -  
 
Introduction  
Thank you for choosing a Newton HD Series speaker. The MC630HD features the finest drivers, precision internal crossover circuitry, and an  
elegant enclosure design.  
The design team at Cambridge SoundWorks believes there is no better combination of audiophile-level attention to detail and reasonable  
cost.  
Contents  
1. One Speaker  
2. Two stick-on rubber feet  
3. Four clear round stick-on rubber feet  
4. Center Channel rear support  
5. ¼-20 machine screw for rear support  
6. Two screws and wall anchors  
After Unpacking  
Save the shipping carton and packing material for future use and transport.  
Inspecting For Damage  
Examine each part carefully for shipping damage. If there is any, do not install or use the speaker. Return the speaker to the merchant where  
you made the purchase or call Cambridge SoundWorks at 1-800 FOR-HIFI (1-800-367-4434) for assistance.  
- -  
 
System Configuration  
For the most balanced performance use an MC630HD on all channels of the surround-sound system. They are also excellent to use as  
rear or surround speakers in a system using MC650HD front speakers. If you prefer smaller or in-wall surround and rear speakers, any of the  
Cambridge SoundWorks Newton Series speakers may be substituted with good results. The Left, Center, and Right speakers should all be the  
same for the most accurate sound stage.  
The MC630HD is intended for use in systems that contain one or more subwoofers, and is not designed to reproduce the deep bass range.  
Use a receiver or AV processor that incorporates a high-pass crossover whenever possible. If you must use the MC630HD with a receiver  
or amplifier that does not contain a high-pass filter, make sure the “o” or “wall” side of the bass contour switch adjacent to the input terminals  
is pressed. Setting this switch to “|” or “Stand” when driven with a full-range signal can result in damage to the speaker if the signal contains  
strong bass.  
Speaker Placement  
The proper placement of speakers affects how well the AV surround system recreates the sound field intended by the recording engineer.  
Current recording practice typically assumes a speaker array with a center channel speaker directly in front of the central viewing position.  
Left and right speakers are placed so they each form a 30 degree angle from the centerline. Left and right surround speakers should be 110  
degrees from the centerline. Left and right rear speakers in a 7.1 system should be at 140 degrees. If a single rear speaker is used in a 6.1  
system, it should be centered on the rear wall. Front speakers should be as close to the height of the TV monitor as practical. Surround and  
rear speakers should be slightly higher. Recreate this speaker pattern as closely as your room and furnishings allow.  
Don’t be too concerned if your situation and listening environment dictate the speakers’ position. Most rooms do not allow ideal placement.  
Place your speakers as close to these guidelines as practical. The speakers will still provide convincing, lifelike sound.  
Your surround processor has a variety of adjustments to optimize the sound based on the speakers’ capabilities and placement. These  
adjustments vary by processor, so refer to your processor’s manual for instructions specific to your equipment. Set your main, center, and  
surround settings to “SMALL”, with subwoofer “ON”. If your processor allows you to adjust the crossover frequency, set it as close to 100Hz as  
possible.  
• Avoid placing front left and right speakers very close to a side wall (within 12-14 inches). The reflected sound from the wall degrades the  
sound coming directly from the speaker.  
RECOMMENDED HOME  
THEATER SETUP  
MAIN SPEAKERS  
MAIN  
SPEAKER  
MAIN  
SPEAKER  
CENTER CHANNEL  
LEVEL  
WITH  
CENTER  
SPEAKER  
SURROUND  
SPEAKER  
SURROUND  
SPEAKER  
POWERED  
SUBWOOFER  
7.1 REAR  
SPEAKER  
7.1 REAR  
SPEAKER  
- -  
 
Wiring The Speakers  
If you wish to conceal the wire within the walls, it is easiest to run  
the wires to their final positions prior to mounting the speakers.  
The spring loaded terminals of the MC630HD accept bare wire  
between AWG #12 and AWG #18 (lower numbers are thicker). It is  
not necessary to “tin” the wire or use connectors to terminate the  
wire.  
Use at least AWG #18 speaker cable for short runs (under 15  
feet). Use AWG #16 or heavier speaker cable for longer runs.  
Building codes typically require plenum rated wire for installation  
within walls. Be sure to use wire that complies with any  
applicable local building codes. Plenum rated cable typically has  
an outer jacket with individually insulated conductors inside the  
outer jacket.  
Preparing The Wires  
1. Determine how long the speaker cable should be for each  
speaker. Cut the speaker cable into the appropriate lengths.  
2. Route the wire to each speaker location.  
Strip 1/2 inch  
3. Strip 1/2 inch of insulation from the two individual conductors  
in the speaker cable. Twist the exposed strands of bare wire  
together.  
4. Determine which conductor you will use to connect the positive  
terminals of the amplifier and speaker together. Printing or a  
ridge on the insulation usually distinguishes one of the two  
conductors. Sometimes the metal of the conductors has two  
different colors, or the insulation color of each conductor may be  
different.  
To Attach The Wires  
1. Press the speaker’s red terminal to expose the hole in its shaft.  
2. Insert the stripped end of one cable’s positive conductor into the  
speaker’s red (+) terminal.  
3. Release the terminal to secure the connection. Make sure no  
stray strands of wire are present.  
4. Repeat the procedure for the cable’s other conductor and the  
speaker’s black (–) terminal.  
5. Connect the opposite end of the speaker cable to the speaker  
outputs of your receiver. Remember to observe channel and  
polarity (Left Positive, Left Negative, Right Positive, Right  
Negative).  
6. Repeat the process for each speaker.  
- -  
 
Speaker Mounting  
The MC630HD may be wall mounted or placed horizontally on a  
table-top as a center-channel using the included hardware. Matching  
floor and table-top stands are available separately from Cambridge  
SoundWorks.  
Hanging The Speaker On The Wall  
The MC630HD may be mounted either vertically or horizontally  
using the supplied wall anchors.  
1. Using the dimension diagram as a guide, mark the position of  
two locations for mounting screws and anchors. The anchors  
will not be needed if you can locate the speakers directly over a  
wall stud. If concealing the wiring in the wall, you should arrange  
the speakers so that the wire exits the wall directly behind  
the center of the speaker. Drill a ¼” diameter hole and install  
wall anchors in each location. Refer to the instructions below  
for proper use of the Toggler brand anchors included with this  
speaker.  
2. Insert the #10 screws into each anchor and screw them partially  
in leaving approximately 3/8” exposed. Test fit the speaker on  
the screws and adjust both screws so that the speaker hangs  
firmly on the wall without rattling.  
3. Attach the wire to the speaker terminals. Slide the speaker on  
the screws from the top.  
®BRAND  
TM  
®
AF6 ALLIGATOR  
Solid-Wall Anchors  
1
1/4"  
Drill 1/4" diameter hole — minimum hole  
1
depth 1 /2". Insert anchor and tap flush.  
2a  
Place item over anchor. Insert screw and  
tighten flush. For best results use screw  
gun for installation in solid walls.  
2b  
In walls of minimum thickness 3/8",  
screw opens anchor and locks securely.  
Use a keyhole slot to hang the speaker from a screwhead.  
Patented under U.S. Patent Nos. 4,752,170 and  
5,161,296; and foreign counterparts thereof.  
Other patents pending. TOGGLER and typeface,  
and ALLIGATOR are worldwide registered  
trademarks of Mechanical Plastics Corp.  
© 2002 MPC  
- -  
 
Placing Horizontally On a Tabletop Or Shelf  
1. Attach the rear support into the channel on the rear of the  
speaker using the included ¼-20 machine screw. Tighten the  
set-screw finger-tight to stabilize the support.  
2. Attach two rubber hook-shaped stick-on feet symmetrically  
along the bottom edge of the speaker approximately 10” apart.  
If you are mounting the speaker on an uneven surface you may  
need to attach the feet closer to the center. Adapt the actual  
position to your needs.  
3. Remove the logo by pulling it straight out. Turn it 90 degrees so  
that the text reads correctly. Press it back in place.  
Logo Orientation  
Rubber Feet  
- -  
 
Setting Bass Contour  
The switch located near the connection terminals optimizes the low  
frequency response of the speaker for wall or stand mounting.  
When the speaker is mounted on a speaker stand, away from  
the wall press the end of the switch marked with “|”.  
When the speaker is mounted on the wall or table, press the  
end of the switch marked with “o”. The upper bass range will  
be slightly attenuated to compensate for the increase in bass  
caused by wall reflection.  
The above recommendations should yield the most accurate  
response in each example, but they are optional. If you prefer the  
sound with settings opposite the above recommendations, feel free to  
use your settings instead.  
Note: Always place the switch in the “o” position if you are  
using amplifier or receiver that does not have a high-pass filter  
on the speaker outputs. Receivers and amplifiers that do not  
have separate subwoofer outputs are in this category.  
Warning About Excessive Amplifier Distortion  
The MC630HD can be safely used with any receiver rated above 30 watts per channel. There is little advantage in using more power than  
100 watts per speaker, but receivers above this power rating can be used so long as the receiver is not operated at distorted levels.  
Operating a receiver (of any power rating) beyond its maximum undistorted output level creates distortion – added high frequency sound not  
part of the musical program. Distortion dramatically increases the internal operating temperature of a speaker and will eventually cause the  
speaker’s failure due to burned or melted internal parts. While Cambridge SoundWorks includes the most heat-tolerant parts commensurate  
with good acoustic design, the speaker’s Limited Warranty against defects in materials or workmanship does not apply to parts that fail from  
long-term operation at very high temperatures.  
Enclosure Cleaning  
The speaker enclosures can be cleaned with a soft, damp cloth or mild cleaner.  
Brush or vacuum the grille panels with a soft brush attachment to your vacuum cleaner.  
In Case of Difficulty  
If you suspect there is a problem with your Newton HD loudspeaker, contact the retailer where it was purchased or a Cambridge  
SoundWorks Audio/Video Consultant, who will help you track down the problem. If together you agree there is something wrong with your  
Newton HD loudspeaker, return it to the retailer that sold it to you. Mail-order and Internet retailers will generally require a Return Authorization  
number. Products purchased from a Cambridge SoundWorks store, you may call us for a factory Return Authorization. Do not return the  
Newton HD loudspeaker or any parts without first obtaining a Return Authorization.  
- -  
 
Specifications  
Dimensions:  
17 5/16” H x 6 1/2” W x 3 7/8” D  
Weight:  
14 pounds each  
Impedance:  
nominal 8 ohms  
Recommended amplifier power range:  
Frequency Range:  
Woofer Type:  
20W – 100W RMS per channel  
80Hz – 24kHz  
2 x 4” with co-injection molded composite cones and butyl-rubber surrounds  
¾” aluminum dome with ferrofluid-damping and neodymium magnet  
2 way, series-connected  
Tweeter Type:  
Crossover:  
Enclosure:  
High-density pressure-cast aluminum with molded-composite baffle  
Dimensions  
3 7/8”  
6 1/2”  
10”  
8 1/4”  
2 7/8”  
3 1/4”  
17 5/16”  
- 10 -  
 
 
120 Water Street  
North Andover, MA 01845  
(800) FOR-HIFI  
(1-800-367-4434)  
P81-2460  
 

Black Box Fax Machine Black Box Network Services FaxReceiver User Manual
Black Box Network Hardware PRO SWITCHING SYSTEM User Manual
Black Decker Toaster TRO1000 User Manual
Bolens Lawn Mower 115 050 000 User Manual
Bosch Power Tools Speaker System DS240 User Manual
Bowers Wilkins Speaker DM605 S2 User Manual
Bushnell Hunting Equipment 119636C User Manual
Campbell Hausfeld Pressure Washer IN470200AV User Manual
Canon Scanner XRD9829REF User Manual
Chicago Electric Musical Toy Instrument 91780 User Manual